Turning off the beeping sound in metal storage cabinets made by manufacturers like Parent Metal Products can be frustrating, but is easily accomplished with a few simple steps. As a top quality metal storage cabinet provider, Parent Metal Products designs their units with an audible beep to alert users if the door is accidentally left open. While helpful in some settings, this persistent beeping can become annoying over time. Luckily, you can disable the beeping with just a Phillips head screwdriver and a few minutes of time.

Locate the Beep Origin

The first step is locating exactly where the beeping sound is coming from within the metal cabinet. In most Parent Metal Products units, there will be a small black plastic box mounted on the inside of the door frame. This box houses the beeper that emits the alert noise.

Carefully inspect the inside of the door frame, sliding your hand along the top edge and sides to feel for the protruding plastic housing. Once located, take note of its specific position before moving to the next step.

Open the Control Box

With the beeper box identified, you can now open it up to access the internal mechanism. Using a Philips head screwdriver, remove the screws holding the plastic cover in place (usually 2-4 screws). Be careful when removing the lid so as not to damage any of the wiring inside.

You should now have the beeper device exposed with access to the speaker, batteries, and control circuitry.

Disable the Beeper

To disable the aggravating beep, you simply need to detach the speaker from the power source. Look for where the two thin speaker wires connect to the circuit board. Gently pull these wire leads out of their socket on the board. You can twist the wires together to prevent accidental reconnection later on.

And just like that – no more beeping! For good measure, you can go ahead and remove the small round batteries from the housing as well.

Reassemble the Box

With the beeper disabled, all that’s left is to reassemble the plastic control box. Place the lid back on aligning the screw holes. Reinsert and tighten the small screws to hold everything in place securely.

Slide the housing back into position on the door frame and test that the door can open and close without any issues. The alert beep should now be permanently silenced!

Alternative Security Options

If you require audible alerts for safety or security reasons, there are alternative options besides the built-in beeper. Many metal storage cabinet companies sell add-on external sirens that can be mounted anywhere on the cabinet. These can be turned on or off as needed.

Motion sensors are another alternative, sending you a smartphone notification if the door is left open instead of an annoying noise. Just make sure to test any battery-powered accessories regularly to avoid failure.

Conclusion

Parent Metal Products designs their storage cabinets to be convenient, safe, and reliable. But constant beeping can undermine those goals in many environments. With just basic DIY skills, you can successfully turn off the alert beeper in any metal cabinet using the steps outlined above. Just locate the control box, disconnect the speaker wires, and reassemble everything as it was. You’ll enjoy peace and quiet once again while maintaining safety. Let us know if you need any help troubleshooting further!

Frequently Asked Questions About Disabling Storage Cabinet Beeping

Here are some common questions people have about turning off the beeping sound in their metal storage cabinets:

Q: Will disabling the beeper affect the door sensor or lighting features?

A: No, only the audible alert is silenced. The door sensor and lighting should continue working normally.

Q: What if I can’t find the beeper box inside my cabinet door?

A: It may be mounted in a different location like the side panel or ceiling. Look carefully along all interior surfaces to locate it.

Q: Is it safe to disable the beeping sound on a flammable storage cabinet?

A: We don’t recommend it. Audible alerts on hazardous material cabinets should remain enabled for safety. Consider alternative options like external sirens instead.

Q: Can I just unplug the beeper instead of disconnecting the wires?

A: You typically can, but it may be more prone to accidental reconnection versus fully detaching the wires.

Q: Will removing the batteries disable the beeping as well as the wires?

A: Yes, depowering the beeper circuit board either way will silence the alarm. Removing batteries is an alternate option.

Q: My cabinet beeps when the door is just slightly open. Can I adjust the sensitivity?

A: Unfortunately no, the trigger point is set internally and can’t be modified. Fully disabling is the only option to prevent accidental beeping.

Q: What are some other methods besides beeping to alert me if a cabinet is left open?

A: Popular alternatives are external sirens, flashing lights, push notifications to your phone, or auto-messaging systems for alerts.

Q: How can I reuse the detached speaker for another purpose?

A: You’d need to provide a new power source, but the speaker could be connected to a DIY microcontroller circuit for other projects.

Q: Will my cabinet manufacturer’s warranty be voided if I disable the beeper?

A: Possibly, you’d have to check the specific terms. But the modification is simple and reversible if needed.

Final Thoughts on Silencing Cabinet Beepers

Having a metal storage cabinet beep constantly can quickly become an annoyance instead of useful alert. With a basic understanding of the internal beeper wiring, you can easily disable these units permanently with common tools. Just remember to still take proper precautions if relying on the audible reminders for hazardous materials or valuables. With the steps provided, you’ll be able to work and focus in peace without the distraction of a loud beeping cabinet.